Use the form below to enter your search criteria. By default, all content is searched except for document comments. If you wish to search comments as well as everything else, click "Also Search Comments" below.
[27]
Comments: 0,
Last Modified: Feb 7, 2018 10:54 AM
- Find Similar
Issue: Cannot connect to the E-MINI over the Ethernet Cause: Ethernet cable not connected OR Network settings are not correct OR User attempting to log in not listed by administrator Solution: Check cable connections OR Configure network settings under Administration | Network OR Have administrator create the user
[31]
Comments: 0,
Last Modified: Feb 7, 2018 10:56 AM
- Find Similar
How many sensors can the E-MINI use? The E-MINI can support up to 7 sensors at a time; 2 cat5 sensors, 4 dry contact sensors, and 1 water sensor. The temperature/humidity combination sensors act as 2 sensors in one, in effect allowing up to 9 sensors if combination sensors are used in the cat5 ports.
[26]
Comments: 0,
Last Modified: Feb 7, 2018 10:53 AM
- Find Similar
Issue: Sensor alerts are not being reported Cause: Network settings are not correct OR No addresses listed to notify Solution: Configure network settings under Administration | Network OR Specify e-mail addresses under Administration | E-mail Specify SNMP IP address in 'Notify Address' box on a sensor configuration page Specify Syslog IP address in 'Notify Address' box
[25]
Comments: 0,
Last Modified: Feb 7, 2018 10:53 AM
- Find Similar
Issue: Sensor readings are not being updated / Sensors are not listed in the Summary Table or the Left Side Menu Cause: Browser is incorrectly going to the cache for updates. (Observed in all versions of Netscape and Firefox browsers) OR Configuration for sensor updates is not set properly Solution ... . This will show a configuration page. On the configuration page, set the following variables: browser
[32]
Comments: 0,
Last Modified: Feb 7, 2018 10:56 AM
- Find Similar
What types of sensors can the E-MINI use? The E-MINI can use combinations of temperature, humidity, door contact, panic button, and tamper switch sensors. It will also operate with any other Dry Contact sensor within specifications.
[196]
Comments: 0,
Last Modified: Feb 8, 2024 5:45 PM
- Find Similar
Cover of the detector as specified and set aside. Place the detector in the palm of your left hand ... the Chamber Cover and the Optical Unit. Set the Chamber Cover onto the Optical Unit while making
[1919]
Comments: 0,
Last Modified: Feb 7, 2018 11:37 AM
- Find Similar
E-SEMS-16(U): How to Turn Off Public SNMP SNMP public access is part of SNMP v1 and v2c. To disable these versions, take the following actions: On the web interface, go to Administration > Settings > SNMP Agent. Uncheck SNMPv1 and SNMPv2c, then press “Apply” to save the settings.
[195]
Comments: 0,
Last Modified: Feb 7, 2018 11:33 AM
- Find Similar
. Solution: 1. Connect a serial cable between a PC and the console port of the E-SEMS-x Unit. Have a Hyperterminal (or other serial com application) open and set to current serial settings ... on. (If the ENVIROMUX-SEMS-16 is still on after the power switch is turned off, press the "Reset
[151]
Comments: 0,
Last Modified: Feb 7, 2018 11:26 AM
- Find Similar
Issue: Get false alerts from the internal humidity sensor every 8 hours to 2 weeks. The alarm email is followed by returned to normal email. Cause: In the sensor configuration, the Sample Period and Alert Delay settings are set too short. Solution: For humidity sensor, set the Sample Period to 10 seconds and the Alert Delay to 30 seconds.
[187]
Comments: 0,
Last Modified: Feb 7, 2018 11:36 AM
- Find Similar
How do I edit the SNMP contact information? The email address contact information used by SNMP to send notifications can be edited by changing the default email address in the Enterprise Settings in the E-SEMS-16 Web Interface. To access the contact information, click "Administration", click "Settings", and "Enterprise" and change the "E-mail" field.
[125]
Comments: 0,
Last Modified: Feb 7, 2018 11:30 AM
- Find Similar
How far can the combination Temperature/Humidity sensor on the E-SEMS-16 be extended? The combination Temperature/Humidity sensor can be extended up to 1000 feet via CAT5/5e/6 cable on the E-SEMS-16. The cables are sold separately.
[173]
Comments: 0,
Last Modified: Feb 7, 2018 11:36 AM
- Find Similar
Passing Login Information with a HTTP Request You can access E-SEMS-16 webpages without manually logging in by using an url in the format: http:// [username]:[password]@[machine-ip]/[page] example: http://root:admin@98.17.207.195/summary_sensor.html However, the request may generate a pop-up alert initially indicating that you are logging in to the machine.
335 results for:
SERIMUX console switch set up windows server 2003,
Displaying results 241 - 255
