Temperature/Humidity Inputs

• Two female RJ45 connectors for connecting temperature sensors, humidity sensors and/or combined temperature/humidity sensors.

Water Detection Cable Input

• One screw terminal pair for connecting liquid detection sensor.
  • Additional water detection sensors can be connected to the dry contact closures.
• Output voltage: +5V DC.
• Current limited to 10mA
• Maximum resistance to close contact: 300K Ohm

Dry Contact Closures

• Four screw terminal pairs for connecting dry contact devices.
• Potential-free.
• Output voltage: +5 V DC
• Current limited to 10 mA
• Maximum resistance to close contact: 300K Ohm

Ethernet Port

• One female RJ45 connector with LEDs.
• 10 BaseT Ethernet interface.

RS232 Port

• One female RJ45 connector for controlling a GSM modem.
• Supports 3-wire interface (Tx, Rx and GND)
• Used for flash upgrades (includes DB9F-RJ45F adapter).
• GSM modem supported: Teltonika WirelessCom/G10

Protocols

• HTTP, SNMP V1, SMTP, TCP/IP, UDP, DHCP, WAP 2.0
• Compatible with any SNMP management software.
• Operates and configures via an HTTP web page.
• An IP address can be assigned to the ENVIROMUX-MINI-CLR automatically by a DHCP server.
• Generates SNMP traps, email alerts, and syslog messages.
• Email alerts can be sent to three addresses.
• Up to four users can access the Web interface simultaneously.
• OIDs for sensor and contact values for ENVIROMUX-MINI-CLR.

Dimensions

• WxDxH (in.): 5.66x2.03x2.02

Environmental

• Operating temperature: 32°F to 100°F (0°C to 38°C).
• Storage temperature: -20°F to 140°F (-30°C to 60°C).
• Operating and Storage Relative Humidity: 17 to 90% non-condensing RH.

Regulatory Approvals

• CE, RoHS

Power

• 110 or 220 VAC at 50 or 60 Hz via AC adapter.
• Power consumption: 5W
• Use the PWR-48V-5V1A or PWR-12V-5V1-5A DC-DC power converter to install the ENVIROMUX-MINI-CLR in a Telecom environment.
• Use the ENVIROMUX-POE Power over Ethernet Adapter to locate the ENVIROMUX Mini up to 300 feet away from a Power Over Ethernet switch.

MTBF

• 80,327 hrs.

Warranty

• Two years

• Configuration can be done over the Internet/LAN via Web page.

Front Panel Interface

• LEDs indicate the following:
  • "Fault" (red) lights up if a sensor goes out of range of a configurable threshold.
  • "Power" (green) lights up when the device is powered/all clear.

Web Interface

• Supports Internet Explorer 6.0 and higher, Firefox 1.5 and higher, Netscape 9, Safari 1.3 and higher for MAC, and Safari 3.0 and higher for PC.
• Configure sensor's thresholds, alarm methods, formats of alerts, and system data log.
• View/edit sensors' current values, thresholds and alert statuses.
  • All sensors connected to the ENVIROMUX-MINI-CLR can be viewed on one summary page.
  • User configurable settings allow sensors to return to normal status when alert condition clears, without manually acknowledging/dismissing the alert.
• View/edit entries stored in the system data log.
• The log can be downloaded as a tab-delimited plain text file.
• Configure IP information (address, subnet mask, default gateway, DNS, etc.), user administrative settings, and data logging settings.
• Up to four users can access the web page at one time.

Mobile Summary Page

View summary page on WAP 2.0 compatible devices (smartphones, PDAs, cell phones, etc.) Supports Blackberry Software 4.2 and higher. Supports iPhones using Safari 3.0 and higher. Summary page lists all connected sensors' current values and alert statuses.

Open Source Monitoring Integration

• SNMP Plugin for Nagios
  • Nagios Product Demo
•   Using Multi Router Traffic Grapher.

Downloads

• Download new firmware and MIB files.